Moritz Fr50 mini felling tractor
Pfanzelt introduced the Moritz mini felling tractor in 2016. The new concept was innovative and pioneering. Building on the success of the Fr50, Pfanzelt introduced the second, enhanced series in 2020. The Fr50 model has therefore been discontinued in this form since the Fr70 and Fr75 models were introduced in the summer of 2020. However, development has continued…
Multipurpose unit
In addition to a permanently installed cable winch Moritz boasts so many more functions to make it suitable for use as an off-road carrier vehicle. The cable winch, installed using a quick-change system, can be removed in only a few steps. You can then mount tools to the vehicle using the three-point mount (cat. 1).
Jungbestandspflege
Manual young plantation care or forest management with a brush cutter (trimmer) is cost and labour intensive. Large storms in recent years, bark beetles and forest fires mean that many areas have been replanted, leading to an increased volume of maintenance work. Forest maintenance is one of the most important areas of forestry. Young plantation care with the Pfanzelt milling machine, which is available for the Moritz Fr50 tracked minitractor, is efficient and high performance.
More details on Moritz mini tractor
Running gear
The chassis width of the Moritz Fr50 can be adjusted to achieve the optimum width for both transport and for off-road operations. The chassis can be hydraulically widened by 400mm. This means that the mini felling tractor can also be safely operated on slopes. The wide chassis and the low dead weight of the caterpillar create a low ground pressure of only 0.30 kg / cm². Even on wet ground, it is thus possible to work and drive without causing damage to the soil. With the front and rear climbing angle of 45°, the mini felling tractor can easily make the transition from forest tracks into the standing timber. The large ground clearance of 300 mm allows the tractor to easily pick its way over roots and stumps and to manoeuvre on forwarding trails.
Secure footing
The stacking shield is the basis for all winching work. This is equipped with double-action hydraulic cylinders. If the weight of the caterpillar is not sufficient for winch work, it can be additionally secured to another object (for example a tree) within a very short time.
The cable infeed height of the mini felling tractor is adjusted. So the height of the cable infeed can be adjusted when in use, this is integrated in the height-adjustable stacking shield.
Wireless control
The entire mini felling tractor can be controlled via an ergonomic remote control. Besides traction drive and winch drive, this also allows adjustment of the cable speed or the engine speed. If the vehicle is not needed for a short time, the engine can also be stopped or started via the remote control.
Attachable implements
Powerful winches
The professional, geared cable winch generates a maximum tractive force of 4 or 5 metric tons and features a cable length of 110 m. Variable cable speed in several stages allows adjustment to different work situations. For tidy cable winding, this can be equipped with a cable infeed brake.
Multipurpose unit
In addition to a permanently installed cable winch Moritz boasts so many more functions to make it suitable for use as an off-road carrier vehicle. The cable winch, installed using a quick-change system, can be removed in only a few steps. You can then mount tools to the vehicle using the three-point mount (cat. 1). A versatile, mechanical PTO is available for tools. The minitractor can also be equipped with hydraulic control units. Consequently different tools meeting different technical requirements can be attached and operated.
Pfanzelt provides a host of different attachments that have been specifically developed for and adapted to the Moritz. These include a mulcher with hydraulic flap, a forestry mulcher with fixed tools, a stump mulcher and a sowing strip mulcher.
Sä milling combination
The new Sä milling combination has been developed in close collaboration with the Federal Forestry Authority of Brandenburg who had already been using it for several months in trials. As part of this process, the milling wheel produces cuts in the forest ground measuring between six and eight cm in depth and cuts fallen branches or small roots with the aim of a particularly good sowing results. The vehicle features different sowing chambers and separate systems for seeding so that both small and large seeds can be processed. A transparent, electronic operating unit enables detailed adjustment of the sowing unit.
Forestry mulcher with hydraulic rear flap and Abrasive forestry tool with hydraulic rear flap
In conjunction with the new forestry mulcher the Moritz has been ideally adapted to different deployment situations to guarantee sustainable application that protects resources. Creating firebreaks also forms part of forestry tasks as does maintaining forests, younger trees and infrastructure plots. The tool can shred shrubbery and undergrowth up to a maximum diameter of 20 cm. Deployments in an agricultural context and to maintain orchards and vineyards are also possible. Moritz is the ideal tracked minitractor for forestry mulching in areas that are difficult to access. The applied hardened metal tools guarantee minimum wear and high levels of efficiency.
Accessories for professionals
The comprehensive range of accessories provides the right equipment for Moritz in any deployment conditions.
An extending, three-part front weight with 110 kg is available for temporary stacking on inclines or to handle cables. Depending on the demands, the vehicle can be equipped with up to three dual-action, hydraulic control units.
Technical specs
| PS RH – 1135/5 | |
|---|---|
| Customize your machine | Configurator |
| Engine | Kubota 4-cylinder diesel engine, power rating 26 kW/ 35 hp, fuel capacity 30 L |
| Drive | Hydrostatic drive, all driving functions can be proportionally adjusted by remote control, driving speed 0 – 6.5 km/h (infinitely adjustable) |
| Running gear | Caterpillar tracks with rubber tracks in AS version, width hydraulically adjustable, hydraulic holding brake |
| Chassis | Torsion-resistant box frame made of special steel, large storage compartment integrated on the chassis, various attachment points for securing the tractor |
| Control | Wireless remote control for all functions (emergency stop, throttle adjustment of diesel engine, driving and steering, winch control, stacking shield, horn) |
| Dimensions | Length 2,200 mm, width 1,120 mm / 1,500 mm, height 1,205 mm, weight 1,050 kg |
| Accessories | |
| Running gear length (1,700 mm) | optional |
| Front weight forwarding tractor | optional (approx. 110 kg – transport box option not possible) |
| Front transport box with attachment | optional (front weight option not possible) |
| Roll bar incl. floodlight | optional |
Front-mounted, auxiliary cable winch
|
optional |
| Cable winch operation accessories | |
Mechanical cable winch 40 kN tractive force
|
optional |
| Hydraulic cable winch, 40 kN tractive force (for technical specs see cable winch with mechanical drive) |
optional |
Mechanical cable winch 50 kN tractive force
|
optional |
| Hydraulic cable winch, 50 kN tractive force (for technical specs see cable winch with mechanical drive) |
optional |
| Cable infeed brake | optional |
| Excavation device – mechanical installation and removal aid for quick change of winch | optional |
| Accessories for multifunction operation | |
| 3-point hitch for detachable implements | optional |
| Water submersion position for hoisting mechanism | optional |
| Tractor PTO transmission | optional |
| Hydraulic auxiliary control valves (up to 3 control valves possible) | optional |
| De-pressurised return for mini felling tractor including bracket | optional |
| Attachments for multifunction operation | |
| Mulcher with 1,200 mm working width (mechanically driven via PTO)
Rotor blade with spirally arranged, special blades to guarantee a constant and equal processing of the mowed area Mechanical lateral displacement (approx. 400 mm) |
optional |
| Mulcher with 1,200 mm working width, additionally with hydraulic flap | optional |
| Forestry mulcher tool featuring hydraulic flap with 1,200 mm working width (mechanically driven via PTO)
With hydraulic flap and mechanical lateral displacement 40 round teeth made of hardened metal that can be used on three sides (turn teeth), arranged spirally 340 mm tool processing diameter, power demand from 20 kW |
optional |
| Lateral hydraulic adjustment for mulcher or forestry mulcher tool | optional |
| Strip mulcher (mechanically driven via PTO)
200 mm mulching depth, v-shaped rift (200 mm wide at the top, 20 mm wide at the bottom) Teeth made of hardened metal |
optional |
| Sowing module with bunker (in conjunction with strip mulcher only)
Separate bunkers for coarse seeds (approximately 55 l capacity) and fine seeds (capacity: 10 l), electrically adjustable sowing frequency, automatic sowing unit deactivation if vehicle comes to standstill, macrolon lid to check contents |
optional |
Videos
Pfanzelt Moritz Fr50 Multifunktionsraupe
Fahrbericht | Pfanzelt Fällraupe Moritz im Einsatz
Forstmulcher im Hang: Was kann die Moritz Fr50 Raupe als Böschungsmäher?
Pfanzelt Forstraupe Moritz Fr50 – Forstmulcher mit hydraulischer Klappe
Forstraupe mit Forstfräse: Was kann die Moritz Fr50 Raupe in der Landschaftspflege?
Pfanzelt Forstraupe Moritz Fr50 – Vorliefern im Steilhang
Fällraupe Moritz im Einsatz bei der Sturmaufarbeitung
Moritz im Einsatz – Vorliefern im Hang
Kundenpräsentation und Interview – Pfanzelt Fäll- und Vorlieferraupe Moritz Fr50
Pfanzelt Fällraupe Moritz im Einsatz
Pfanzelt Fällraupe Moritz Fr50
Elmia Wood 2017: Felling mini-tractor Pfanzelt Maschinenbau Moritz FR50
